Kubota U35-4 Excavator Workshop Service Manual

Kubota U35-4 Excavator Workshop Service Manual

$33.00

Publication: RY921-21840
Format: PDF
Language: English
Kubota U35-4 Excavator Workshop Manual – 514 Pages

Categories: ,

Description

Kubota U35-4 Excavator Workshop Service Manual

Kubota Excavator Model U35-4
Publication: RY921-21840
Format: PDF
Language: English
Kubota U35-4 Excavator Workshop Manual – 514 Pages

Table of Content of the Workshop Service Manual

I General
II Machine body
• Mechanism Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .II-M-1
• Service Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .II-S-1
V Electrical System
IV Hydraulic System
• Mechanism Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IV-M-1
• Service Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IV-S-1
III Engine
• Mechanism Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .III-M-1
• Service Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .III-S-1
IV Orbitrol motor ; structure & function

U35-4
Your KUBOTA dealer is always ready to help so that your excavator offers the best performance. After having carefully read this manual, you will realize that much of the routine maintenance can be done by yourself. Machines must be disassembled and assembled efficiently and safely. It is very important to thoroughly understand the construction and function of the machine, to make all appropriate preparations, and start operations according to the specified working procedures in this workshop service manual.

IMPORTANT INSPECTION ITEMS AFTER REASSEMBLING

a Operate the Kubota U35-4 Excavator and check for Unusual Noise and Vibrations.
b Make Sure the Safety decals and Wire harness Clamps are in their Specified Positions.
c With the Machine Front in a Specified Posture, Check the Amount of Hydrauric Oil Checking the oil level (For further details, refer to the Excavator U35-4 Operator’s Manual)
1) Park the machine on a level ground.
2) Make sure the hydraulic oil temperature is in the range of 10-30°C (50-86°F) and see if the oil level is within the specified zone of the oil level gauge.
3) Keep the machine front as shown as following posture.

Evaporator
The evaporator takes the refrigerant, which has been made liquid by the condenser and cooled and put under low-pressure by the expansion valve, and by evaporating it, the heat and humidity of the air passing through the evaporator is removed, thus producing cool, dehumidified air.
Heater Core
The heater core dissipates the heat of the heated engine coolant. So, the air that is blown through it by the blower motor passes through the fins of the heater
Blower
The blower is built into the right side of the AC unit.
The blower forces cool, warm or fresh outside air through the vents into the cabin.
The rpm of the blower motor can be adjusted to three levels with the blower resistor. The blower fan is the type that uses centrifugal force and it sucks in air parallel to its axis of rotation and blows it out perpendicular to the centrifugal force, or in other words, perpendicular to the axis of rotation.

  • Workshop Manual
  • SECTION 1 GENERAL INFORMATION
    Group 1 Precautions for disassembling and
    Assembling
    Group 2 Tightening Torque
    Group 3 Painting
    Group 4 Bleeding Air from Hydraulic Oil Tank
    SECTION 2 UPPERSTRUCTURE
    Group 1 Cab
    Group 2 Counterweight
    Group 3 Main Frame
    Group 4 Pump Device
    Group 5 Control Valve
    Group 6 Swing Device
    Group 7 Pilot Valve
    Group 8 Pilot Shut-Off Valve
    Group 9 Signal Control Valve
    Group 10 Travel Shockless Valve
    Group 11 Solenoid Valve
    Group 12 Pilot Relief Valve
    Group 13 Steering Valve
    Group 14 Brake Valve
    Group 15 Accumulator Charging Valve
    Group 16 Transmission Control Valve
    SECTION 3 UNDERCARRIAGE
    Group 1 Swing Bearing
    Group 2 Travel Motor
    Group 3 Center Joint
    Group 4 Transmission
    Group 5 Axle
    Group 6 Axle Lock Cylinder
    Group 7 Operate-Check Valve
    Group 8 Propeller Shaft
    SECTION 4 FRONT ATTACHMENT
    Group 1 Front Attachment
    Group 2 Cylinder
    Group 3 Hose-Rupture Safety Valve
    Group 4 Operate-Check Valve
    SECTION 5 ENGINE

    Service Manual (Troubleshooting)
    SECTION 4 OPERATIONAL PERFORMANCE
    TEST
    Group 1 Introduction
    Group 2 Standard
    Group 3 Engine Test
    Group 4 Excavator Test
    Group 5 Component Test
    Group 6 Adjustment
    SECTION 5 TROUBLESHOOTING
    Group 1 General
    Group 2 Component Layout
    Group 3 Troubleshooting A
    Group 4 Troubleshooting B
    Group 5 Troubleshooting C
    Group 6 Electrical System Inspection
    Group 7 ICX

Reviews

There are no reviews yet.


Be the first to review “Kubota U35-4 Excavator Workshop Service Manual”

You've just added this product to the cart: