Case JXU70, JXU80, JXU90, JXU100 Tractor Service Manual

Description

Table of Contents

SECTION 00 – GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SECTION 10 – ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SECTION 18 – CLUTCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SECTION 21 – FRONT TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SECTION 23 – 4WD TRANSFER BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SECTION 25 – MFD AXLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SECTION 27 – REAR TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SECTION 31 – POWER TAKE-OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SECTION 33 – BRAKES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SECTION 35 – HYDRAULIC SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SECTION 41 – STEERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
SECTION 44 – WHEEL AXLES (2WD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
SECTION 55 – ELECTRICAL SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
SECTION 90 – PLATFORM, CAB, BODYWORK AND DECALS . . . . . . . . . . . 20

The following pages are the collation of the contents pages from each section and chapter of the JXU Series Repair manual. Complete Repair Manual # 87020289.

Manual Extract: CHECKING THE ALIGNMENT OF THE LEADING WHEELS

Check the alignment of the leading wheels, bearing in mind that for driving in a straight line, the wheels must be at an angle of 2° to the ground, corresponding to a difference of approximately 0.6 in. (15 mm), for 16” rims, between the top and bottom edges of the rim (fig. a).

When driving in a straight line, the wheels must also be parallel to longitudinal axis of the tractor, or have a maximum of 0.2 in. (5 mm) toe–in at the front, as measured between the edges of the rims.

To check the toe–in exactly, proceed as follows:

1. Inflate the front tires to a pressure of 36.2 psi (2.5 bar).
2. Position the steering wheel at the middle of its travel, with one spoke along the longitudinal axis of the tractor.
3. Check that the wheels are parallel with the longitudinal axis of the tractor.
4. On the horizontal plane passing between the centres of the wheels, measure the distance (B) between the front inside edges of the rims (see fig. b).
5. On the horizontal plane passing between the centres of the wheels, measure the distance between the rear inside edges of the rims, checking that the distance is equal to (B) or exceeds it by up to a maximum of 0.2 in. (5 mm).
6. If necessary, correct the toe–in by adjusting the end of the transverse steering tie–rod.