Kubota KX36-3, KX41-3S, KX41-3V Excavator Workshop Manual

$34.00

Publication: 97899-60860
Format: PDF
Language: English
Kubota KX36-3, KX41-3S, KX41-3V Excavator Manual (Service Chapter) – 496 Pages
Kubota KX36-3, KX41-3S, KX41-3V Excavator Manual (Mechanism Chapter) – 130 Pages

Categories: ,

Description

Kubota KX36-3, KX41-3S, KX41-3V Excavator Workshop Manual

Kubota Excavator Model KX36-3, KX41-3S, KX41-3V
Publication: 97899-60860
Format: PDF
Language: English
Kubota KX36-3, KX41-3S, KX41-3V Excavator Manual (Service Chapter) – 496 Pages
Kubota KX36-3, KX41-3S, KX41-3V Excavator Manual (Mechanism Chapter) – 130 Pages

Table of Content of the Workshop Service Manual

I General
II Machine Body
III Engine
IV Hydraulic System
V Electrical System

KX36-3, KX41-3S, KX41-3V
Your KUBOTA dealer is always ready to help so that your excavator offers the best performance. After having carefully read this manual, you will realize that much of the routine maintenance can be done by yourself. Machines must be disassembled and assembled efficiently and safely. It is very important to thoroughly understand the construction and function of the machine, to make all appropriate preparations, and start operations according to the specified working procedures in this workshop service manual.

IMPORTANT INSPECTION ITEMS AFTER REASSEMBLING

a Operate the Kubota KX36-3, KX41-3S, KX41-3V Excavator and check for Unusual Noise and Vibrations.
b Make Sure the Safety decals and Wire harness Clamps are in their Specified Positions.
c With the Machine Front in a Specified Posture, Check the Amount of Hydrauric Oil Checking the oil level (For further details, refer to the Excavator KX36-3, KX41-3S, KX41-3V Operators Manual)
1) Park the machine on a level ground.
2) Make sure the hydraulic oil temperature is in the range of 10-30C (50-86F) and see if the oil level is within the specified zone of the oil level gauge.
3) Keep the machine front as shown as following posture.

Checking and Adjusting the Excavator Engine Body
Compression Pressure
1. Run the engine until it is warmed up.
2. Stop the engine.
3. Remove the air cleaner, the muffler, the head cover and all glow plugs.
4. Set a compression tester (Code No. 07909-30208) with the adaptor (Adaptor K, code No. 07909-291) to the glow plug hole.
5. After making sure that the stop lever is set at the stop position (non-injection), run the engine with the starter and measure the compression pressure.
6. Repeat steps 4 and 5 for each cylinder.
7. If the measurement is below the allowable limit, apply a small amount of oil to the cylinder wall through the glow plug hole and measure the compression pressure again.
8. If the compression pressure is still less than the allowable limit, check the top clearance, valve clearance and cylinder head.
9. If the compression pressure increases after applying oil, check the cylinder wall and piston rings.Compression Pressure
1. Run the engine until it is warmed up.
2. Stop the engine.
3. Remove the air cleaner, the muffler, the head cover and all glow plugs.
4. Set a compression tester (Code No. 07909-30208) with the adaptor (Adaptor K, code No. 07909-291) to the glow plug hole.
5. After making sure that the stop lever is set at the stop position (non-injection), run the engine with the starter and measure the compression pressure.
6. Repeat steps 4 and 5 for each cylinder.
7. If the measurement is below the allowable limit, apply a small amount of oil to the cylinder wall through the glow plug hole and measure the compression pressure again.
8. If the compression pressure is still less than the allowable limit, check the top clearance, valve clearance and cylinder head.
9. If the compression pressure increases after applying oil, check the cylinder wall and piston rings.

Reviews

There are no reviews yet.


Be the first to review “Kubota KX36-3, KX41-3S, KX41-3V Excavator Workshop Manual”